Address of the bookmark: http://qb.cshl.edu/genomescope/

Run Maq Now

Follow these steps to try Maq. All you need is a reference sequence file in the FASTA format.

1. Prepare a reference sequence (ref.fasta). Better a bacterial genome.
2. Download maq, maq-data and maqview at the download page.
3. Copy maq, maq.pl and maq_eval.pl to the $PATH or to the same directory.
4. Simulate diploid reference and read sequences, map reads, call variants and evaluate the results in one go:

   maq.pl demo ref.fasta calib-30.dat
   

   where calib-30.dat is contained in maq-data.
5. View the alignment:

   cd maqdemo/easyrun;
   maqindex -i -c consensus.cns all.map;
   maqview -c consensus.cns all.map

Even for advanced maq users, running `maq.pl demo' is recommended. You may find something helpful.

Address of the bookmark: http://maq.sourceforge.net

More at https://github.com/aaronwolen/liftover

https://www.bioconductor.org/help/workflows/liftOver/

Address of the bookmark: https://github.com/aaronwolen/liftover

• Inchworm assembles the RNA-seq data into the unique sequences of transcripts, often generating full-length transcripts for a dominant isoform, but then reports just the unique portions of alternatively spliced transcripts.

• Chrysalis clusters the Inchworm contigs into clusters and constructs complete de Bruijn graphs for each cluster. Each cluster represents the full transcriptonal complexity for a given gene (or sets of genes that share sequences in common). Chrysalis then partitions the full read set among these disjoint graphs.

• Butterfly then processes the individual graphs in parallel, tracing the paths that reads and pairs of reads take within the graph, ultimately reporting full-length transcripts for alternatively spliced isoforms, and teasing apart transcripts that corresponds to paralogous genes.

More at https://github.com/trinityrnaseq/trinityrnaseq/wiki

......................................................................................................................................

Download Trinity here.

Build Trinity by typing 'make' in the base installation directory.

Assemble RNA-Seq data like so:

 Trinity --seqType fq --left reads_1.fq --right reads_2.fq --CPU 6 --max_memory 20G 

Find assembled transcripts as: 'trinity_out_dir/Trinity.fasta'

Address of the bookmark: https://github.com/trinityrnaseq/trinityrnaseq/wiki

• paired-end (PE) and/or mate-pair libraries (NGS-based mode)
• long reads (NGS-based mode)
• synteny to the genome of some related species (reference-based mode)

Scaffolding 

In reference-based mode, pyScaf uses synteny to the genome of closely related species in order to order contigs and estimate distances between adjacent contigs.

Contigs are aligned globally (end-to-end) onto reference chromosomes, ignoring:

• matches not satisfying cut-offs (--identity and --overlap)
• suboptimal matches (only best match of each query to reference is kept)
• and removing overlapping matches on reference.

In preliminary tests, pyScaf performed superbly on simulated heterozygous genomes based on C. parapsilosis (13 Mb; CANPA) and A. thaliana (119 Mb; ARATH) chromosomes, reconstructing correctly all chromosomes always for CANPA and nearly always for ARATH (Figures in dropbox, CANPA table, ARATH table).
Runs took ~0.5 min for CANPA on 4 CPUs and ~2 min for ARATH on 16 CPUs.

Important remarks:

• Reduce your assembly before (fasta2homozygous.py) as any redundancy will likely break the synteny.
• pyScaf works better with contigs than scaffolds, as scaffolds are often affected by mis-assemblies (no de novo assembler / scaffolder is perfect...), which breaks synteny.
• pyScaf works very well if divergence between reference genome and assembled contigs is below 20% at nucleotide level.
• pyScaf deals with large rearrangements ie. deletions, insertion, inversions, translocations. Note however, this is experimental implementation!
• Consider closing gaps after scaffolding.

Address of the bookmark: https://github.com/lpryszcz/pyScaf

http://www.ncbi.nlm.nih.gov/pubmed/23307812

http://bioen-compbio.bioen.illinois.edu/RACA/

Address of the bookmark: http://bioen-compbio.bioen.illinois.edu/RACA/

DISCOVAR can call variants on a region by region basis, potentially tiling an entire large genome. DISCOVAR variant calling is under active development and transitioning to VCF.

DISCOVAR de novo can generate de novo assemblies for both large and small genomes. It currently does not call variants.

More at https://www.broadinstitute.org/software/discovar/blog/?page_id=14

Address of the bookmark: https://www.broadinstitute.org/software/discovar/blog/

Blaxter Lab, Institute of Evolutionary Biology, University of Edinburgh

Goal: To create blobplots or Taxon-Annotated-GC-Coverage plots (TAGC plots) to visualise the contents of genome assembly data sets as a QC step.

This repository accompanies the paper:
Blobology: exploring raw genome data for contaminants, symbionts and parasites using taxon-annotated GC-coverage plots. Sujai Kumar, Martin Jones, Georgios Koutsovoulos, Michael Clarke, Mark Blaxter
(submitted 2013-10-01 to Frontiers in Bioinformatics and Computational Biology special issue : Quality assessment and control of high-throughput sequencing data).

It contains bash/perl/R scripts for running the analysis presented in the paper to create a preliminary assembly, and to create and collate GC content, read coverage and taxon annotation for the preliminary assembly, which can be visualised, such as Figure 2a from the paper showing TAGC plots/blobplots for Caenorhabditis sp. 5: 

Address of the bookmark: https://github.com/blaxterlab/blobology

https://github.com/aalokaily/Hierarchical-Genome-Assembly-HGA

Address of the bookmark: https://github.com/aalokaily/Hierarchical-Genome-Assembly-HGA

Address of the bookmark: http://sb.nhri.org.tw/CISA/en/CISA