An algorithmically novel approach to construct a genome graph representation of long-read-based de novo sequence assemblies. We then provide a proof of principle by creating a genome graph of seven ethnically-diverse human genomes.

https://f1000research.com/articles/7-1391/v1

Address of the bookmark: https://github.com/NCBI-Hackathons/NovoGraph

Address of the bookmark: http://omega.omicsbio.org/

So far miniasm is in early development stage. It has only been tested on a dozen of PacBio and Oxford Nanopore (ONT) bacterial data sets. Including the mapping step, it takes about 3 minutes to assemble a bacterial genome. Under the default setting, miniasm assembles 9 out of 12 PacBio datasets and 3 out of 4 ONT datasets into a single contig. The 12 PacBio data sets are PacBio E. coli sample, ERS473430, ERS544009, ERS554120, ERS605484, ERS617393, ERS646601, ERS659581, ERS670327, ERS685285, ERS743109 and a deprecated PacBio E. coli data set. ONT data are acquired from the Loman Lab.

For a C. elegans PacBio data set (only 40X are used, not the whole dataset), miniasm finishes the assembly, including reads overlapping, in ~10 minutes with 16 CPUs. The total assembly size is 105Mb; the N50 is 1.94Mb. In comparison, the HGAP3produces a 104Mb assembly with N50 1.61Mb. This dotter plot gives a global view of the miniasm assembly (on the X axis) and the HGAP3 assembly (on Y). They are broadly comparable. Of course, the HGAP3 consensus sequences are much more accurate. In addition, on the whole data set (assembled in ~30 min), the miniasm N50 is reduced to 1.79Mb. Miniasm still needs improvements.

Miniasm confirms that at least for high-coverage bacterial genomes, it is possible to generate long contigs from raw PacBio or ONT reads without error correction. It also shows that minimap can be used as a read overlapper, even though it is probably not as sensitive as the more sophisticated overlapers such as MHAP and DALIGNER. Coupled with long-read error correctors and consensus tools, miniasm may also be useful to produce high-quality assemblies.

Minimap and miniasm are ultrafast tools for (i) mapping and (ii) assembly. Designed for long, noisy reads, they do not have a correction or consensus step, and therefore the resulting assemblies are contiguous (i.e. long) but very noisy (i.e. full of errors)

We start with an all against all comparison:

minimap -Sw5 -L100 -m0 -t8 reads.fq reads.fq | gzip -1 > reads.paf.gz

Then we can assemble

miniasm -f reads.fq reads.paf.gz > reads.gfa

Convert GFA to FASTA:

awk '/^S/{print ">"$2"\n"$3}' reads.gfa | fold > reads.fa

And then count how many contigs:

grep ">" reads.fa | wc -l

# Download sample PacBio from the PBcR website
wget -O- http://www.cbcb.umd.edu/software/PBcR/data/selfSampleData.tar.gz | tar zxf -
ln -s selfSampleData/pacbio_filtered.fastq reads.fq
# Install minimap and miniasm (requiring gcc and zlib)
git clone https://github.com/lh3/minimap && (cd minimap && make)
git clone https://github.com/lh3/miniasm && (cd miniasm && make)
# Overlap
minimap/minimap -Sw5 -L100 -m0 -t8 reads.fq reads.fq | gzip -1 > reads.paf.gz
# Layout
miniasm/miniasm -f reads.fq reads.paf.gz > reads.gfa

Address of the bookmark: https://github.com/lh3/miniasm

Address of the bookmark: https://github.com/marbl/MashMap

y a number of metrics, including:

• Overall assembly length
• Number of scaffolds/contigs
• Length of longest scaffold/contig
• Scaffold/contig N50 and N90Assembly base composition, in particular percentage GC and percentage Ns
• CEGMA completeness
• Scaffold/contig length/count distribution

assembly-stats supports two widely used presentations of these values, tabular and cumulative length plots, and introduces an additional circular plot that summarises most commonly used assembly metrics in a single visualisation. Each of these presentations is generated using javascript from a common (JSON) data structure, allowing toggling between alternative views, and each can be applied to a single or multiple assemblies to allow direct comparison of alternate assemblies.

Tabular presentation allows direct comparison of exact values between assemblies, the limitations of this approach lie in the necessary omission of distributions and the challenge of interpreting ratios of values that may vary by several orders of magnitude.

Address of the bookmark: https://github.com/rjchallis/assembly-stats

Address of the bookmark: http://hibberdlab.com/transrate/index.html

Source code, executables and the testing dataset are freely available at https://github.com/mapleforest/HaploMerger2/releases/.

Address of the bookmark: https://github.com/mapleforest/HaploMerger2/releases/

We accomplish this by first calculating genotype likelihoods for every site. For a given site in a diploid genome, there are 10 possible genotypes (AA, AC, AG, AT, CC, CG, CT, GG, GT, TT). Referee takes as input the genotype likelihoods calculated for all 10 genotypes given the called reference base at each position.

Referee is a program to calculate a quality score for every position in a genome assembly. This allows for easy filtering of low quality sites for any downstream analysis.

https://github.com/gwct/referee

Address of the bookmark: https://gwct.github.io/referee/#