Our work is published in Scientific Reports:

Ye, C. et al. DBG2OLC: Efficient Assembly of Large Genomes Using Long Erroneous Reads of the Third Generation Sequencing Technologies. Sci. Rep. 6, 31900; doi: 10.1038/srep31900 (2016).

http://www.nature.com/articles/srep31900

The manual can be downloaded from:

https://github.com/yechengxi/DBG2OLC/raw/master/Manual.docx

To use precompiled versions,please go to:

https://github.com/yechengxi/DBG2OLC/tree/master/compiled

Address of the bookmark: https://github.com/yechengxi/DBG2OLC

Address of the bookmark: https://github.com/philres/ngmlr

Address of the bookmark: https://github.com/baoe/flas

https://academic.oup.com/ve/article/7/1/veab042/6248116

Address of the bookmark: https://academic.oup.com/ve/article/7/1/veab042/6248116

1. "m" = movie
2. Time of Run Start (yymmdd_hhmmss)
3. Instrument Serial Number
4. SMRT Cell Barcode
5. Set Number (a.k.a. "Look Number". Deprecated field, used in earlier version of RS)
6. Part Number (usually "p0", "X0" when using expired reagents)
7. ZMW hole number
8. Subread Region (start_stop using polymerase read coordinates)
9. readScore
10. barcodeScore

So far miniasm is in early development stage. It has only been tested on a dozen of PacBio and Oxford Nanopore (ONT) bacterial data sets. Including the mapping step, it takes about 3 minutes to assemble a bacterial genome. Under the default setting, miniasm assembles 9 out of 12 PacBio datasets and 3 out of 4 ONT datasets into a single contig. The 12 PacBio data sets are PacBio E. coli sample, ERS473430, ERS544009, ERS554120, ERS605484, ERS617393, ERS646601, ERS659581, ERS670327, ERS685285, ERS743109 and a deprecated PacBio E. coli data set. ONT data are acquired from the Loman Lab.

For a C. elegans PacBio data set (only 40X are used, not the whole dataset), miniasm finishes the assembly, including reads overlapping, in ~10 minutes with 16 CPUs. The total assembly size is 105Mb; the N50 is 1.94Mb. In comparison, the HGAP3produces a 104Mb assembly with N50 1.61Mb. This dotter plot gives a global view of the miniasm assembly (on the X axis) and the HGAP3 assembly (on Y). They are broadly comparable. Of course, the HGAP3 consensus sequences are much more accurate. In addition, on the whole data set (assembled in ~30 min), the miniasm N50 is reduced to 1.79Mb. Miniasm still needs improvements.

Miniasm confirms that at least for high-coverage bacterial genomes, it is possible to generate long contigs from raw PacBio or ONT reads without error correction. It also shows that minimap can be used as a read overlapper, even though it is probably not as sensitive as the more sophisticated overlapers such as MHAP and DALIGNER. Coupled with long-read error correctors and consensus tools, miniasm may also be useful to produce high-quality assemblies.

Minimap and miniasm are ultrafast tools for (i) mapping and (ii) assembly. Designed for long, noisy reads, they do not have a correction or consensus step, and therefore the resulting assemblies are contiguous (i.e. long) but very noisy (i.e. full of errors)

We start with an all against all comparison:

minimap -Sw5 -L100 -m0 -t8 reads.fq reads.fq | gzip -1 > reads.paf.gz

Then we can assemble

miniasm -f reads.fq reads.paf.gz > reads.gfa

Convert GFA to FASTA:

awk '/^S/{print ">"$2"\n"$3}' reads.gfa | fold > reads.fa

And then count how many contigs:

grep ">" reads.fa | wc -l

# Download sample PacBio from the PBcR website
wget -O- http://www.cbcb.umd.edu/software/PBcR/data/selfSampleData.tar.gz | tar zxf -
ln -s selfSampleData/pacbio_filtered.fastq reads.fq
# Install minimap and miniasm (requiring gcc and zlib)
git clone https://github.com/lh3/minimap && (cd minimap && make)
git clone https://github.com/lh3/miniasm && (cd miniasm && make)
# Overlap
minimap/minimap -Sw5 -L100 -m0 -t8 reads.fq reads.fq | gzip -1 > reads.paf.gz
# Layout
miniasm/miniasm -f reads.fq reads.paf.gz > reads.gfa

Address of the bookmark: https://github.com/lh3/miniasm

Address of the bookmark: https://github.com/bcgsc/ARCS/

https://www.nature.com/articles/nmeth.4432

Address of the bookmark: https://github.com/xiaochuanle/MECAT

Here is how I use the blasr to align PacBio reads to the contigs (target.fasta). The “target.fasta.sa” is the suffix array from “target.fasta” generated by sawriter.

blasr query.fa ./target.fasta -sa ./target.fasta.sa -bestn 40 -maxScore -500 -m 4 -nproc 24 -out target.m4 -maxLCPLength 15

the output format option “-m 4″ generate the alignment coordinate. Not fully documented, but I can explain that to you. 

I use a 24 cores / 48G ram server for the alignment. It took about 2 to 3 hours aligning 3G PacBio Reads to 10^6 sequences of short read contigs with a mean 3.5kbp length.

Address of the bookmark: http://bix.ucsd.edu/projects/blasr/