So far miniasm is in early development stage. It has only been tested on a dozen of PacBio and Oxford Nanopore (ONT) bacterial data sets. Including the mapping step, it takes about 3 minutes to assemble a bacterial genome. Under the default setting, miniasm assembles 9 out of 12 PacBio datasets and 3 out of 4 ONT datasets into a single contig. The 12 PacBio data sets are PacBio E. coli sample, ERS473430, ERS544009, ERS554120, ERS605484, ERS617393, ERS646601, ERS659581, ERS670327, ERS685285, ERS743109 and a deprecated PacBio E. coli data set. ONT data are acquired from the Loman Lab.

For a C. elegans PacBio data set (only 40X are used, not the whole dataset), miniasm finishes the assembly, including reads overlapping, in ~10 minutes with 16 CPUs. The total assembly size is 105Mb; the N50 is 1.94Mb. In comparison, the HGAP3produces a 104Mb assembly with N50 1.61Mb. This dotter plot gives a global view of the miniasm assembly (on the X axis) and the HGAP3 assembly (on Y). They are broadly comparable. Of course, the HGAP3 consensus sequences are much more accurate. In addition, on the whole data set (assembled in ~30 min), the miniasm N50 is reduced to 1.79Mb. Miniasm still needs improvements.

Miniasm confirms that at least for high-coverage bacterial genomes, it is possible to generate long contigs from raw PacBio or ONT reads without error correction. It also shows that minimap can be used as a read overlapper, even though it is probably not as sensitive as the more sophisticated overlapers such as MHAP and DALIGNER. Coupled with long-read error correctors and consensus tools, miniasm may also be useful to produce high-quality assemblies.

Minimap and miniasm are ultrafast tools for (i) mapping and (ii) assembly. Designed for long, noisy reads, they do not have a correction or consensus step, and therefore the resulting assemblies are contiguous (i.e. long) but very noisy (i.e. full of errors)

We start with an all against all comparison:

minimap -Sw5 -L100 -m0 -t8 reads.fq reads.fq | gzip -1 > reads.paf.gz

Then we can assemble

miniasm -f reads.fq reads.paf.gz > reads.gfa

Convert GFA to FASTA:

awk '/^S/{print ">"$2"\n"$3}' reads.gfa | fold > reads.fa

And then count how many contigs:

grep ">" reads.fa | wc -l

# Download sample PacBio from the PBcR website
wget -O- http://www.cbcb.umd.edu/software/PBcR/data/selfSampleData.tar.gz | tar zxf -
ln -s selfSampleData/pacbio_filtered.fastq reads.fq
# Install minimap and miniasm (requiring gcc and zlib)
git clone https://github.com/lh3/minimap && (cd minimap && make)
git clone https://github.com/lh3/miniasm && (cd miniasm && make)
# Overlap
minimap/minimap -Sw5 -L100 -m0 -t8 reads.fq reads.fq | gzip -1 > reads.paf.gz
# Layout
miniasm/miniasm -f reads.fq reads.paf.gz > reads.gfa

Address of the bookmark: https://github.com/lh3/miniasm

Address of the bookmark: https://github.com/marbl/MashMap

y a number of metrics, including:

• Overall assembly length
• Number of scaffolds/contigs
• Length of longest scaffold/contig
• Scaffold/contig N50 and N90Assembly base composition, in particular percentage GC and percentage Ns
• CEGMA completeness
• Scaffold/contig length/count distribution

assembly-stats supports two widely used presentations of these values, tabular and cumulative length plots, and introduces an additional circular plot that summarises most commonly used assembly metrics in a single visualisation. Each of these presentations is generated using javascript from a common (JSON) data structure, allowing toggling between alternative views, and each can be applied to a single or multiple assemblies to allow direct comparison of alternate assemblies.

Tabular presentation allows direct comparison of exact values between assemblies, the limitations of this approach lie in the necessary omission of distributions and the challenge of interpreting ratios of values that may vary by several orders of magnitude.

Address of the bookmark: https://github.com/rjchallis/assembly-stats

This script has been modified by others to convert InDels as well, e.g. this by David Eccles

./vcf2fq.pl -f <input.fasta> <all-site.vcf> > <output.fastq>

https://github.com/gringer/bioinfscripts/blob/master/vcf2fq.pl

https://github.com/lh3/samtools/blob/master/bcftools/vcfutils.pl

Source code for SKESA is freely available at https://github.com/ncbi/SKESA/releases.

Research Paper @ Link

SKESA algorithm are as follows:

Address of the bookmark: https://github.com/ncbi/SKESA/releases

QUAST-LG is included in the QUAST  package starting from version 5.0.0 (download the latest release). Run QUAST as usual and do not forget to add ‐‐large option to your command!

A short list of the new features (see CHANGES for all):

• Significant speedup achieved by both use of new fast aligner (minimap2) and the refactoring of alignment analyzing modules
• New k-mer-based completeness and correctness metrics
• BUSCO added for enhanced reference-free analysis
• The concept of upper bound assembly (theoretical limits on the assembly completeness and contiguity for a given genome and set of reads)

Address of the bookmark: http://cab.spbu.ru/software/quast-lg/

I have used the following assemblers

• Spades (v. 3.10.1)
• CANU (v. 1.6)
• Unicycler (v. v0.4.1)
• Miniasm (v. 0.2-r137-dirty)

I have used the following mappers

• minimap2 (v. 2.0rc1-r232)
• minimap (v. 0.2-r124-dirty)
• bwa (v. 0.7.12-r1039)

I have used the following polishing tools

• Racon (v. not available)
• Pilon (v. 1.18)
• Nanopolish (v. 0.8.3)

I have used the following tools to assess genome assembly characteristics

• ANI.pl (https://github.com/chjp/ANI)
• CheckM (v. 1.0.7)
• Prokka (v. 1.12)
• QUAST (v. 2.3)
• mummer (v. not available)

If you have any ideas or superior tools we have missed please let us know in the comments.

./wtdbg2 -x rs -g 4.6m -t 16 -i reads.fa.gz -fo prefix
./wtpoa-cns -t 16 -i prefix.ctg.lay.gz -fo prefix.ctg.fa

Address of the bookmark: https://github.com/ruanjue/wtdbg2

Address of the bookmark: https://sourceforge.net/projects/contiguator/