Our work is published in Scientific Reports:

Ye, C. et al. DBG2OLC: Efficient Assembly of Large Genomes Using Long Erroneous Reads of the Third Generation Sequencing Technologies. Sci. Rep. 6, 31900; doi: 10.1038/srep31900 (2016).

http://www.nature.com/articles/srep31900

The manual can be downloaded from:

https://github.com/yechengxi/DBG2OLC/raw/master/Manual.docx

To use precompiled versions,please go to:

https://github.com/yechengxi/DBG2OLC/tree/master/compiled

Address of the bookmark: https://github.com/yechengxi/DBG2OLC

I made Rebaler for bacterial genomes (specifically for the task of testing basecallers). It should in principle work for non-bacterial genomes as well, but I haven't tested it.

Address of the bookmark: https://github.com/rrwick/Rebaler

More at https://academic.oup.com/bib/advance-article-abstract/doi/10.1093/bib/bbab022/6146772

Address of the bookmark: https://github.com/huangs001/AlignGraph2

Porechop also supports demultiplexing of Nanopore reads that were barcoded with the Native Barcoding Kit, PCR Barcoding Kit or Rapid Barcoding Kit.

Address of the bookmark: https://github.com/rrwick/Porechop

So far miniasm is in early development stage. It has only been tested on a dozen of PacBio and Oxford Nanopore (ONT) bacterial data sets. Including the mapping step, it takes about 3 minutes to assemble a bacterial genome. Under the default setting, miniasm assembles 9 out of 12 PacBio datasets and 3 out of 4 ONT datasets into a single contig. The 12 PacBio data sets are PacBio E. coli sample, ERS473430, ERS544009, ERS554120, ERS605484, ERS617393, ERS646601, ERS659581, ERS670327, ERS685285, ERS743109 and a deprecated PacBio E. coli data set. ONT data are acquired from the Loman Lab.

For a C. elegans PacBio data set (only 40X are used, not the whole dataset), miniasm finishes the assembly, including reads overlapping, in ~10 minutes with 16 CPUs. The total assembly size is 105Mb; the N50 is 1.94Mb. In comparison, the HGAP3produces a 104Mb assembly with N50 1.61Mb. This dotter plot gives a global view of the miniasm assembly (on the X axis) and the HGAP3 assembly (on Y). They are broadly comparable. Of course, the HGAP3 consensus sequences are much more accurate. In addition, on the whole data set (assembled in ~30 min), the miniasm N50 is reduced to 1.79Mb. Miniasm still needs improvements.

Miniasm confirms that at least for high-coverage bacterial genomes, it is possible to generate long contigs from raw PacBio or ONT reads without error correction. It also shows that minimap can be used as a read overlapper, even though it is probably not as sensitive as the more sophisticated overlapers such as MHAP and DALIGNER. Coupled with long-read error correctors and consensus tools, miniasm may also be useful to produce high-quality assemblies.

Minimap and miniasm are ultrafast tools for (i) mapping and (ii) assembly. Designed for long, noisy reads, they do not have a correction or consensus step, and therefore the resulting assemblies are contiguous (i.e. long) but very noisy (i.e. full of errors)

We start with an all against all comparison:

minimap -Sw5 -L100 -m0 -t8 reads.fq reads.fq | gzip -1 > reads.paf.gz

Then we can assemble

miniasm -f reads.fq reads.paf.gz > reads.gfa

Convert GFA to FASTA:

awk '/^S/{print ">"$2"\n"$3}' reads.gfa | fold > reads.fa

And then count how many contigs:

grep ">" reads.fa | wc -l

# Download sample PacBio from the PBcR website
wget -O- http://www.cbcb.umd.edu/software/PBcR/data/selfSampleData.tar.gz | tar zxf -
ln -s selfSampleData/pacbio_filtered.fastq reads.fq
# Install minimap and miniasm (requiring gcc and zlib)
git clone https://github.com/lh3/minimap && (cd minimap && make)
git clone https://github.com/lh3/miniasm && (cd miniasm && make)
# Overlap
minimap/minimap -Sw5 -L100 -m0 -t8 reads.fq reads.fq | gzip -1 > reads.paf.gz
# Layout
miniasm/miniasm -f reads.fq reads.paf.gz > reads.gfa

Address of the bookmark: https://github.com/lh3/miniasm

In this report, we compare and evaluate several genome assembly software based on TSG technology. The experimentation has been performed on 4 reference genomes and the results evaluated with the QUAST software. The 11 software that have been evaluated are: Celera Assembler , Falcon , Miniasm, Newbler , SGA Assembler, Smartdenovo, Abruijn, Ra, DBG2OLC, Spades and Cerulean. The first 8 software use only long reads, while the 3 last software can merge long and short reads

NextDenovo contains two core modules: NextCorrect and NextGraph. NextCorrect can be used to correct TGS long reads with approximately 15% sequencing errors, and NextGraph can be used to construct a string graph with corrected reads. It also contains a modified version of minimap2 for adapting input and output and producing more sensitive and accurate dovetail overlaps, and some useful utilities (see here for more details).

Address of the bookmark: https://github.com/Nextomics/NextDenovo

The assembly process can be summarized as follows:

1. overlap
2. patch reads
3. overlap (again)
4. scrubbing
5. assembly graph construction and touring
6. optional read correction
7. fasta file creation

Address of the bookmark: https://github.com/schloi/MARVEL

Input

Jabba takes as input a concatenated de Bruijn graph and a set of sequences:

the de Bruijn graph should appear in fasta format with 1 entry per node, the meta information should be in the format:
>NODE
the set of sequences should be in fasta or fastq format. These sequences will be corrected (e.g. PacBio reads). The corrections will be written to a file Jabba fasta.
The output is a file in fasta format with corrections of the long reads, and additionally a file in the input format containing uncorrected reads.

https://github.com/biointec/jabba/wiki

https://almob.biomedcentral.com/articles/10.1186/s13015-016-0075-7

Address of the bookmark: https://github.com/biointec/jabba